The job that went through 6 mm plywood in one pass last month now needs two, and the second pass leaves a darker edge than you'd like. Nothing else has changed. Same file, same board, same settings. Most owners blame the lens first, and sometimes that's right, but sooner or later the CO₂ laser tube itself is the part that's getting tired. This guide explains what the tube is, how to read its specs, what wears it out and how to tell when it's really time for a new one.
Key Takeaway
- A CO₂ laser tube is a sealed gas tube that makes a 10.6 µm infrared beam
- Glass tubes are water-cooled consumables and RF metal tubes last far longer
- Rated power and peak power on a spec sheet are not the same thing
- Rule out mirrors and the lens and cooling before you blame the tube
- A replacement has to match the length and wattage and power supply
1. What Is a CO₂ Laser Tube?
A CO₂ laser tube is the part of your machine that actually makes the laser. It's a sealed tube filled with a gas mix of carbon dioxide, nitrogen and helium. When high voltage or radio-frequency energy excites that gas, it emits an infrared beam at 10.6 µm, which the mirrors carry to the lens.
a. What is inside the tube
The gas is mostly not carbon dioxide. A sealed tube holds roughly 10 to 20% CO₂ and a similar share of nitrogen, with helium making up most of the rest, according to the overview of the carbon-dioxide laser on Wikipedia. At each end sits a mirror. One reflects everything back, the other lets a small share of the light out as the beam. A glass tube also has an outer water jacket wrapped around the gas chamber to carry heat away.

b. How the beam is made
The electrical discharge excites the nitrogen first. Nitrogen holds that energy for a while and hands it to the CO₂ molecules when they collide, and the CO₂ releases it as infrared light. Helium's job is to cool things down so the cycle can keep going, which is why this explainer on CO₂ lasers calls it essential to the process. That light bounces between the mirrors, builds up and leaves through the partial mirror as a beam you can't see.

2. Glass vs RF Metal Tubes
There are two kinds of tube in engraving machines. A DC glass tube is long, water-cooled and cheaper, and it's the usual choice for cutting. An RF metal tube is shorter, sealed in metal, often air-cooled and lasts much longer, and its small spot makes it better for fine engraving.
a. DC glass tubes
Glass tubes are excited by high-voltage direct current from a separate power supply. They're long because power comes with length, and they need a chiller to keep the coolant in a narrow temperature band. They cut well and cost less up front, which is why they dominate the larger cabinet machines. They're also fragile, and their output fades as they age.

b. RF metal tubes
An RF tube is excited by radio frequency through electrodes in a metal body. It switches on and off far faster than a glass tube, so it can hold detail at high engraving speeds, and its beam focuses to a much smaller dot. There's more on how they work in our article on the RF laser tube, and a straight comparison in glass vs RF CO₂ laser.

c. Which OneLaser machines use which
- RF only: the XRF desktop machine and the VertiGo drinkware laser, both on a 38W RF tube.
- Glass only: the XT desktop machine with a 55W glass tube, and the Cobra 8, 10 and 14 cabinet machines.
- Both: the Hydra Gen2 machines, which pair a glass tube for cutting with an RF tube for engraving in one cabinet.
3. How to Read a CO₂ Laser Tube Spec Sheet
A CO₂ laser tube spec sheet tells you more than the wattage. Look at rated power, peak power, length, diameter, working current and the cooling range. Rated power is what the tube is built to deliver all day, peak power is a short-term ceiling, and the current figures tell you how hard you can drive it safely.
OneLaser's replacement glass tubes for the Hydra make a good worked example. All three are 80 mm across and water-cooled at 15 to 25 °C, and they differ in length and power:
- C100 (Hydra 9): 1,450 mm long, 100 W rated and 130 W peak, recommended current 24 mA and a maximum of 25 mA.
- C130 (Hydra 13): 1,650 mm long, 130 W rated and 150 W peak, recommended 28 mA and a maximum of 30 mA.
- C150 (Hydra 16): 1,850 mm long, 150 W rated and 180 W peak, recommended 28 mA and a maximum of 30 mA.
Two things are worth noticing. The extra 200 mm between each model is where the extra power comes from, so a bigger tube won't fit a cabinet built for a smaller one. And the gap between recommended and maximum current is small, which is why running a glass tube flat out shortens its life. The full sheets are on the CO₂ glass laser tube page.
An RF tube's sheet reads differently. The 38W tube in the XRF is listed with a 100 MHz RF frequency, a waveguide resonator, beam quality under M² 1.2 and air or water cooling, and you won't find a current figure because it isn't driven by a high-voltage supply.

4. How Long Does a CO₂ Laser Tube Last?
A glass CO₂ laser tube is a consumable. OneLaser's own figure is roughly 1,500 to 3,000 hours of use, depending on power, cooling and care, while the RF tube in the XRF is rated for up to 30,000 hours. Heat and current are what use a glass tube up fastest.
Those hours aren't a cliff edge. A glass tube fades slowly, so the first sign is usually that cuts need a bit more power or a bit less speed than they used to. Glass tubes also age on the shelf, so a spare that has sat in a cupboard for two years won't be as fresh as a new one. Idle time matters as well as hours of use. A glass tube that sits unused through a hot, humid summer can come back weaker than one that ran a little every week, because heat speeds up the slow gas loss through the seals. If your machine will stand for a long time, keep it somewhere cool and dry, and fire it briefly every few weeks. We go through the numbers for every laser type in how long laser engravers last.
5. Signs Your CO₂ Laser Tube Is Failing
The clearest sign is lost power: cuts that used to go through in one pass now need two, and engraving looks paler at the same settings. Other signs are a change in the glow inside a glass tube, arcing, or visible cracks. Before you order a tube, check the optics and the cooling, because they cause the same symptoms.
a. Power loss and extra passes
Keep a note of a reference cut, a set thickness of one material at fixed settings. When that cut stops going through, you've got a real measurement instead of a feeling. If the drop is gradual over months, the tube is the likely cause. If it happened overnight, look elsewhere first.
b. Colour change or weak glow
A healthy glass tube shows an even glow along the discharge while it fires. An uneven, flickering or noticeably different colour can mean the gas mix has changed or air has crept in. Watch it with the lid closed and the machine's own viewing window between you and the beam.
c. Arcing and cracks
Arcing at the high-voltage end, a crack in the glass or coolant inside the gas chamber means the tube is finished or about to be. Stop using the machine. Our guide to CO₂ laser tube arcing explains what's safe to check and what isn't.
d. Rule out mirrors, lens and cooling first
A dirty lens or a fogged mirror can cost a surprising amount of power, and so can a beam that's drifted off-centre. Clean and inspect the laser lens and mirrors, check alignment, and confirm the coolant is cool and flowing. Only then blame the tube.

6. How to Make a CO₂ Laser Tube Last Longer
A tube lasts longest when it runs below its maximum, stays cool and isn't working against dirty optics. For a glass tube that means keeping power at roughly 50 to 70%, holding coolant at 15 to 25 °C with clean distilled water, and cleaning the lens and mirrors on a schedule.
- Cap the power. Set a maximum in your software below 100% and slow down instead when a cut needs more.
- Look after the coolant. Use distilled water, keep bubbles out of the line and never fire the tube with the chiller off. Our comparison of water-cooled vs air-cooled machines explains why it matters so much more for glass.
- Keep the optics clean. Every percent of power lost at a dirty lens is a percent the tube has to make up.
- Mind the room. Heat and humidity are hard on tubes, in use and in storage.
RF tubes need less fuss, mainly clear airflow around their fins. Our RF and CO₂ maintenance guide has a full checklist.
7. Replacing a CO₂ Laser Tube
Replacing a tube means buying one that matches your machine's length, wattage and power supply, disconnecting the old one safely, and realigning the beam afterwards. A glass tube swap is within reach of a careful owner. An RF tube is usually replaced as a complete unit, so check with support first.
a. Match length, wattage and power supply
The new tube has to fit the cradle in your cabinet, and its current rating has to suit your power supply. A higher-wattage tube is longer and wants more current, so it rarely drops into the same machine. OneLaser lists which CO₂ glass laser tube fits each Hydra, and the XRF uses its own RF metal laser tube.
b. Safety before you touch it
A glass tube's power supply works at tens of kilovolts. Switch off and unplug the machine, give the supply time to discharge, then drain the coolant before you loosen anything. Handle the tube by its body, never by the high-voltage lead, and keep it level so water doesn't run into the ends.
c. After the swap
A new tube almost never lines up exactly with the old one, so expect to realign the first mirror at least. Our guide to laser beam alignment walks through it. Then run your reference cut again so you've got a new baseline for the next time the tube starts to fade.
Before you order, write down what's printed on the old tube's label, measure its length end to end and note the wattage your machine was sold with. Those three details are what support will ask for first. Keep the old tube's packaging if the new one arrives in it, because a long glass tube is far safer to store or return in its original box than wrapped in towels. And plan the swap for a quiet day: draining, fitting, refilling and realigning usually takes longer the first time than people expect.
8. FAQ
How long does a CO₂ laser tube last?
A glass tube lasts roughly 1,500 to 3,000 hours by OneLaser's figures, depending on power and cooling. RF tubes last many times longer.
How do I know if my CO₂ laser tube is bad?
Your reference cut no longer goes through at the same settings, and clean optics and good cooling don't bring it back. Cracks or arcing settle the question.
Can I replace the tube myself?
A glass tube, yes, if you're careful with the high voltage and realign the beam afterwards. For an RF tube, talk to support first.
What is the difference between a glass and an RF laser tube?
Glass tubes are DC-excited, water-cooled and cheaper. RF tubes are metal, often air-cooled, focus to a smaller dot and last far longer.
Can I put a higher-wattage tube in my machine?
Usually not. A more powerful glass tube is longer and needs a stronger power supply, so it won't fit or run safely without other changes.