It usually starts as a sound. A dry crackle from the back of the machine, a bit like a bug zapper, every time the laser fires. Then the cuts get weaker, and one evening with the lights down you catch a blue flicker near the end of the tube. That's CO₂ laser tube arcing: the high voltage that's supposed to go through the gas has found a shortcut to ground. It needs dealing with, and it needs dealing with carefully.
Key Takeaway
- Arcing is stray electricity and has nothing to do with the beam
- The pink glow inside a working tube is normal
- Switch off and unplug before you look closely at anything
- Connections and insulation fail far more often than tubes
- Damp air and very cold coolant both make it worse
- RF metal tubes don't have the exposed high-voltage lead that arcs
1. What Is CO₂ Laser Tube Arcing?
CO₂ laser tube arcing is what happens when the voltage driving a glass tube jumps across open air to something grounded, such as the frame or a mount, because that route has become easier than the one through the gas. You'll hear crackling or buzzing, you may see a spark or a faint blue glow, and cutting power drops.

A DC glass tube takes a very high voltage to get the gas excited, and that voltage arrives along a single insulated lead at the anode end. As long as the insulation is sound, all of it goes into the tube. Give it a weak spot anywhere along the way and some of it leaves early.
People often mistake the normal glow for a fault, so it's worth being clear about that. The pink light you see drifting around inside the glass is excited gas, and it's meant to be there. There's a good exchange about normal plasma movement on the LightBurn forum where an owner gets reassured on exactly this point. The beam itself you can't see at all. Arcing happens outside the gas path, and it's noisy.

The other clue is performance. Energy that escapes as an arc never makes it into the beam, so a machine that's arcing is usually a machine that's losing cutting power as well.
2. Is CO₂ Laser Tube Arcing Dangerous?
Yes, and this is the part to read slowly. The voltage on a glass tube can seriously hurt or kill you, and an arc that's left alone will chew through the power supply, the tube and the wiring around it. Stop the job, switch off, pull the plug and give it several minutes before you open the tube bay.
Don't put a hand anywhere near the tube circuit with the machine powered, and don't go hunting for the spark with a screwdriver. If you haven't been trained to work on high-voltage equipment, that's fine. Your job here is to look, take notes and hand it to a technician.
3. What Causes a Laser Tube to Arc?
Something has made it easier for the voltage to go around the tube than through it. In practice that's a loose or cracked connection, insulation that has worn through near the metal frame, moisture in the air or on the glass, coolant that has started to conduct, or a tube or power supply near the end of its life.
a. A loose or cracked high-voltage connection
If you only check one thing, check the joint where the lead meets the anode pin. A poor connection there, or an insulating sleeve that has split with age, lets the current jump to the frame or the tube mount.
b. Damaged insulation or a lead routed near metal
Insulation doesn't last forever. Heat hardens it and vibration cracks it. The nasty part is what happens next: once an arc has burned a carbon track into the surface, that track conducts, and the arc comes back to the same spot again and again.
c. Humidity and condensation
Wet air gives way more easily than dry air. And if your chiller is set colder than the room, water condenses on the glass and does the same thing. That's part of why water-cooled vs air-cooled machines behave so differently in a muggy workshop.
d. Contaminated coolant
Fresh distilled or deionized water hardly conducts at all. Water that's been going round the loop for a year picking up minerals and algae is another matter, and it can end up as part of the arc's path. Fill the system with the right coolant and change it when the manual says to.
e. An ageing tube or power supply
Electrodes wear and power supplies drift, and both lead to an unstable discharge. None of this is new. A US patent on arcing in gas lasers from decades ago describes oxide building up on an electrode until hot spots form and arcs start from them.

For a sense of how messy this gets in real life, read Christian Chauvin's posts. He started a long diagnosis thread on the LightBurn forum about a CO₂ machine he'd bought in 2020. The tube and the power supply would begin buzzing and crackling together and the output would sag. By the time he posted, he had already replaced both the tube and the supply, and nothing had changed.
The replies are a small masterclass. One member said it sounded like corona discharge, which is high voltage leaking to ground, and named insulation failure, humidity and condensation from cold cooling water as the likely reasons. Ed Nisley identified an arc near the cathode end reaching the cooling water cap, and told him to replace that run of wire and go over the high-voltage wiring. A couple of others suggested swapping in fresh, non-conductive coolant, since it's cheap to try. The thread ends without a confirmed fix, so I can't tell you which one it was. What it does show is two expensive parts bought before the wiring was looked at.
4. How to Find and Fix the Arc, Step by Step
Locate it with the covers shut, then do your inspecting with the machine off and unplugged. Go through the connections first, then the route the lead takes, then moisture and coolant, and leave the tube and the power supply until last. The cheap causes are also the common ones, so check them before you order parts.
- Watch from outside. Dim the lights, keep the covers closed and fire a short, low-power test. Look through the window for a blue flicker and note where it is.
- Shut it down properly. Off at the switch, plug out of the wall, and wait several minutes.
- Look at the high-voltage end. You're after a cracked sleeve, a scorch mark or a joint that isn't seated at the anode.
- Follow the lead back. Check for chafed insulation and anywhere the lead rests against the frame.
- Deal with moisture. Wipe off any condensation and bring the coolant temperature up into the range your manual gives.
- Change the coolant. Flush the loop and refill with clean distilled or deionized water.
- Hand over the repair. Anything involving the lead, the joint or the supply itself is a technician's job.
a. What not to do
- Don't keep running jobs and hope. Each arc burns the insulation a bit more, which makes the next one easier.
- Don't patch a damaged lead with ordinary electrical tape. It isn't rated for anything like this voltage.
- Don't turn the power up to make up for weak cuts. More current just feeds the arc.
- Don't run the chiller colder thinking you're protecting the tube. Colder water means more condensation.
It also pays to keep notes while you work: where the flicker was, how humid the room felt, the coolant temperature, what you changed and when. CO₂ laser tube arcing tends to come and go, and there's nothing more frustrating than a technician arriving on the one day it behaves. A few lines in a notebook give them something to go on.
Steps five and six belong in your regular tube and cooling maintenance anyway. Kept up, they head off a lot of arcing before it starts.

5. Glass Tube vs RF Tube: Why RF Machines Do Not Arc This Way
Everything above is specific to DC glass tubes. An RF laser tube is built differently: it's a sealed metal unit, and the gas is excited by radio-frequency energy. There's no long high-voltage lead running to a glass end cap and no water jacket around the discharge, so the arc paths described here aren't present.
If you're comparing the two, our guide to RF vs glass tube lasers lays out the trade-offs, and there's a separate explainer on how an RF laser tube works.
To be fair to glass, it still gives you more cutting power for the money, and RF machines have fault alarms of their own. But if you're spending your weekends chasing sparks and changing coolant, it's reasonable to ask whether an RF desktop machine would suit the work you do.
6. When to Replace the Tube
Replace the tube if the arc is inside the glass, if you can see burning around an electrode, or if power stays low after you've proved the wiring and the coolant are good. A tube showing those signs late in its rated life isn't going to recover, and nursing it along usually costs more in ruined jobs.
As a rough yardstick, one general guide gives typical tube lifespans of around 8,000 to 20,000 hours for CO₂ lasers, while OneLaser rates its RF metal tubes at up to 30,000 hours. We go into the detail in how long laser tubes last. Hydra owners who do need one can order a replacement glass tube directly.
7. FAQ
What does laser tube arcing sound like?
A sharp crackle, a buzz or a steady hiss that begins when the laser fires. It often seems to come from the tube and the power supply at the same moment.
Can bad cooling water cause laser tube arcing?
It can play a part. Contaminated water conducts, and it can end up in the arc's path. Flush the system and refill with clean distilled or deionized water.
Is the pink glow inside my CO₂ tube normal?
Yes. That's excited gas, and a bit of movement and flicker is expected. Arcing happens outside the gas path and you'll usually hear it.
Does arcing mean my laser tube is dead?
Not necessarily. A lot of arcing comes from a connection, worn insulation or moisture, so check those before you buy a tube.
Do RF laser tubes arc?
Not like this. They're sealed metal units with no exposed high-voltage DC lead, though they do have fault alarms of their own.